Super Lowest Price Rs422 Multiplexer - Framed E1-FE+8RS232 interface Converter JHA-CE1F1R8 – JHA

Framed E1-FE+8RS232 interface Converter JHA-CE1F1R8

Overview

This protocol converter (interface converter) using large scale FPGA design, providing a framing E1 interface and an Ethernet interface and 8channel RS232/422/485,it is possible to achieve 10 / 100Base-T Ethernet data over E1 channels transmission, is a high performance, self-learning Ethernet bridge. The device serves as an extension of Ethernet devices, use of existing networks (PDH / SDH / microwave, etc.) provided by the E1 channels to interconnect both ends of the lower cost Ethernet and serial interfaces. Built-loop test equipment capabilities to facilitate the opening and routine maintenance works.

Product Photo

19inch 1U Type

Features

• Based on self -copyright IC
• Can realize monitor and control of remote equipment, OAM management data did not take up user’s timeslot and save E1 bandwidth
• E1 supports any timeslot set, the rate is 64K-2048K
• The local device can forced the remote device rate follow it
• Have indicator  when the remote device is power-off or E1 line is broken or lose signal;
• Have the function of E1 interface loop back check, avoid the converter crashed because of interface loop return;
• The Ethernet interface supports jumbo frames (2036 Bytes);
• Inter-set dynamic Ethernet MAC address (4,096) with local data frame filtering function
• Ethernet interface supports 10M/100M, half/full duplex auto- Negotination, support VLAN
• Ethernet interface supports AUTO-MDIX (crossed line and straightly connected line self-adaptable );
• Have Ethernet monitor self-reset function, the equipment will not dead
• Provide 2 clock types: E1 master clock and E1 line clock;
• Provide 2 impedances: 75 Ohm unbalance and 120 Ohm balance;
• Support SNMP Network Management
• Serial Data Interface can be RS232/RS422/RS485/TTL optional
• Serial channel can transmit adaptable serial data asynchronously 300 Kbps-19200Kbps baud rate
• Serial data multiplexing in E1 support ITU-T R.111 jumping coding mode
• The local RS232 serial data can command the remote RS232 serial data loop-back to the local. This loop-back in the outer ring of RS232 data interface, you can test the RS232 interface chip without damage
• Serial port interface lightning-protection reached IEC61000-4-5 (8/20μS) DM(Differential Mode): 6KV, Impedance (2 Ohm), CM(Common Mode): 6KV, Impedance (2 Ohm)standard

Parameters

♦ E1 Interface

Interface Standard: comply with protocol G.703;
Interface Rate: n*64Kbps±50ppm;
Interface Code: HDB3;

E1 Impedance: 75Ω (unbalance), 120Ω (balance);

Jitter tolerance: In accord with protocol G.742 and G.823

Allowed Attenuation: 0~6dBm

♦ Ethernet interface(10/100M)

Interface rate: 10/100 Mbps, half/full duplex auto-negotiation

Interface Standard:     Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)

MAC Address Capability: 4096

Connector:     RJ45, support Auto-MDIX

♦ Serial Interface

Standard

  EIA/TIA-232 RS-232 (ITU-T V.28)

  EIA/TIA-422 RS-422 (ITU-T V.11)

  EIA/TIA-485 RS-485 (ISO/IEC8284)

  Serial Interface

  RS-422:TXD+, TXD-, RXD+, RXD-, Signal Ground

  RS-485 4 wires: TXD+, TXD-, RXD+, RXD-, Signal Ground

  RS-485 2 wires: Data+(Correspond TX+), Data-（Correspond TX-）, Signal Ground

  RS-232: RXD, TXD, Signal Ground

♦ Working environment

Working temperature:    -10°C ~ 50°C

Working Humidity:     5%~95 % (no condensation)

Storage temperature: -40°C ~ 80°C

Storage Humidity:  5%~95 % (no condensation)

Specifications

Application