Low MOQ for Optical Module - 10/100/1000BASE-T Copper SFP Transceiver JHA3401 – JHA

Features:                                              

♦ Up to 1.25Gb/s bi-directional data links

♦ Hot-pluggable SFP footprint

♦ Extended case temperature range (-40°C to +85°C )

♦ Fully metallic enclosure for low EMI

♦ Low power dissipation

♦ Compact RJ-45 connector assembly

♦ Detailed product information in EEPROM

♦ +3.3V single power supply

♦ Access to physical layer IC via 2-wire serial bus

♦ 10/100/1000 BASE-T operation in host systems with SGMII interface

♦ Compliant with SFP MSA

♦ Compliant with IEEE Std 802.3TM-2002

♦ Compliant with FCC 47 CFR Part 15, Class B

♦ RoHS Compliant Products

Applications:

♦ 1.25 Gigabit Ethernet over Cat 5 cable

♦ Switch/Router to Switch/Router Link

♦ High speed I/O for file severs

Description:

JHA3401 10/100/1000BASE-T copper SFP transceiver is high performance, cost effective module compliant with the Gigabit Ethernet and 10/100/1000BASE-T standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which supporting 10/100/1000Mbps data- rate up to 100 meters reach over unshielded twisted-pair category 5 cable. The JHA3401 supports 10/100/1000 Mbps full duplex data-links with 5-level Pulse Amplitude Modula-tion (PAM) signals. All four pairs in the cable are used with symbol rate at 250Mbps on each pair. The JHA3401 provides standard serial ID information compliant with SFP MSA, which can be accessed with address of A0h via the 2-wire serial CMOS EEPROM protocol. The physical IC can also be accessed via 2-wire serial bus at address ACh.

• SFP to Host Connector Pin Out

Notes:

1. TX Fault is not used and is always tied to ground through a 100 ohm resistor.

2. TX Disable as described in the MSA is not applicable to the 1000BASE-T module, but is used for convenience as an input to reset the internal ASIC. This pin is pulled up within the module with a 4.7 KW resistor.

Low (0 – 0.8 V): Transceiver on

Between (0.8 V and 2.0 V): Undefined

High (2.0 – 3.465 V): Transceiver in reset state

Open: Transceiver in reset state

3. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7-10 KW resistor on the host board to a supply less than VCCT + 0.3 V or VCCR + 0.3 V.

Mod Def 0 is tied to ground through a 100 ohm resistor to indicate that the module is present.

Mod-Def 1 is clock line of two wire serial interface for optional serial ID

Mod-Def 2 is data line of two wire serial interface for optional serial ID

4. LVTTL compatible with a maximum voltage of 2.5V. Not supported on HTSFP-24-111X

5. RD-/+: These are the differential receiver outputs. They are ac coupled 100 ohm differential lines which should be terminated with 100 ohm differential at the user SerDes. The ac coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 2000 mV differential (185 – 1000 mV single ended) when properly terminated. These levels are compatible with CML and LVPECL voltage swings.

6. VCCR and VCCT are the receiver and transmitter power supplies. They are defined as 3.3 V ± 5% at the SFP connector pin. The maximum supply current is about 300mA and the associated in-rush current will typically be no more than 30 mA above steady state after 500 nanoseconds.

7. TD-/+: These are the differential transmitter inputs. They are ac coupled differential lines with 100 W differential termination inside the module. The ac coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 –1200 mV single ended), though it is recommended that values between 500 and 1200 mV differential (250 – 600 mV single ended) be used for best EMI performance. These levels are compatible with CML and LVPECL voltage swings.

Diagram of host board connector block pin numbers and names

• +3.3V Volt Electrical Power Interface

The JHA3401 has an input voltage range of 3.3 V +/- 5%. The 4 V maximum voltage is not allowed for continuous operation.

Caution: Power consumption and surge current are higher than the specified values in the SFP MSA

• Low-Speed Signals

MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals. Both MOD_ DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc.

• High-Speed Electrical Interface

All high-speed signals are AC-coupled internally.

 • General Specifications

• Environmental Specifications

The JHA3401 has an extended range from 0°C to +85°C case temperature as specified in Table 7.

• Serial ID Memory Contents

• Mechanical Dimensions

Mechanical Dimensions of Transceiver

JHA reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such products or information.

Published by Shenzhen JHA Technology Co., Ltd

Copyright © Shenzhen JHA Technology Co., Ltd

All Rights Reserved