China Wholesale SFP-10g-Lr Quotes Manufacturer - 155M Single Mode 120Km DDM | Single Fiber SFP Transceiver JHA520CD-54 – JHA

 Features:                                              

* Up to 155Mb/s Data Links

* Hot-Pluggable

*  Duplex LC connector

* Up to 120Km on 9/125μm SMF

*  1550nm DFB laser transmitter

*  1490nm PIN photo-detector

* Single +3.3V Power Supply

*  Monitoring Interface Compliant with SFF-8472

*  Maximum Power <1W

*  Industrial /Extended/ Commercial operating temperature range: -40°C to 85°C/-5°C to 85°C/-0°C to 70°C Version available

* RoHS compliant

Applications:

* 1000Base-EZX Ethernet

* Metro/Access Networks

* 1×Fibre Channel

* Other Optical Links

Description:

JHA520CD-54 Transceivers are a high performance, cost effective module which have a single LC optics interface. They are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA). The receiver section uses a PIN receiver and the transmitter uses a 1550 nm DFB laser, up to 31dB link budge ensure this module 1000Base-EZX Ethernet 120km application.

Absolute Maximum Ratings

Recommended Operating Enviorment:

Electrical Characteristics (T_OP = 0 to 70 °C, VCC = 3.135 to 3.465 Volts)

Note:

1. AC coupled.
2. Or open circuit.
3. Into 100 ohm differential termination.
4. 20 – 80 %
5. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
6. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 14, 2000.

Optical Parameters(T_OP = 0 to 70°C, VCC = 3.135 to 3.465 Volts)

Note:

1. The optical power is launched into SMF.
2. 20-80%.
3. Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253.
4. Measured with PRBS 27-1 at 10-12 BER

Pin Assignment

Diagram of Host Board Connector Block Pin Numbers and Name

Pin Function Definitions

Note:

1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in.
4. Rate select is not used
5. LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
6. AC Coupled

SFP Module EEPROM Information and Management

The SFP modules implement the 2-wire serial communication protocol as defined in the SFP -8472. The serial ID information of the SFP modules and Digital Diagnostic Monitor parameters can be accessed through the I2C interface at address A0h and A2h. The memory is mapped in Table 1. Detailed ID information (A0h) is listed in Table 2. And the DDM specification at address A2h. For more details of the memory map and byte definitions, please refer to the SFF-8472, “Digital Diagnostic Monitoring Interface for Optical Transceivers”. The DDM parameters have been internally calibrated.

Table 1. Digital Diagnostic Memory Map (Specific Data Field Descriptions)

Table 2 - EEPROM Serial ID Memory Contents (A0h)

Digital Diagnostic Monitor Characteristics

Regulatory Compliance

The JHA520CD-5 complies with international Electromagnetic Compatibility (EMC) and international safety requirements and standards (see details in Table following).

Recommended Circuit

SFP Host Recommended Circuit

Mechanical Dimensions

JHA reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such products or information.Published by Shenzhen JHA Technology Co., Ltd.

Copyright © JHA

All Rights Reserved