China Wholesale 155m SFP 80km Suppliers Factories - 1.25G Single Mode 40Km DDM | 1550nm Tx/1310nm Rx, Single Fiber SFP Transceiver, JHA5440D-53 – JHA

Features:                                              

1). Up to 1.25Gb/s Data Links 

2). Hot-Pluggable

3). Single LC connector

4). Up to 40 km on 9/125μm SMF

5). 1550nm DFB laser transmitter

6). 1310nm PIN photo-detector

7). Single +3.3V Power Supply

8). Monitoring Interface Compliant with SFF-8472

9). Maximum power dissipation <1W

10). Industrial /Extended/ Commercial operating temperature range: -40°C to 85°C/-5°C to 85°C/-0°C to 70°C Version available

11). RoHS compliant and Lead Free

Applications:

 1). 1000Base-LX Ethernet 

2). Metro/Access Networks

 3). 1×Fibre Channel 

4). Other Optical Links  

 Description:  

JHA5440D-53 Transceivers are a high performance, cost effective module which have a single LC optics interface. They are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA) and Digital diagnostics functions are available via the 2-wire serial bus specified in SFF-8472. The receiver section uses a PIN receiver and the transmitter uses a 1550 nm DFB laser, up to 21dB link budge ensure this module 1000Base-EX Ethernet 40km application.

 • Absolute Maximum Ratings

• Recommended Operating Environment:

• Electrical Characteristics(T_OP = -40 to 85°C, VCC = 3.135 to 3.465 Volts)

Note:

1. AC coupled.
2. Or open circuit.
3. Into 100 ohm differential termination.
4. 20 – 80 %
5. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
6. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 14, 2000.

• Optical Parameters(T_OP = -40 to 85°C, VCC = 3.135 to 3.465 Volts)

Note

1. The optical power is launched into SMF.
2. 20-80%.
3. Contributed total jitter is calculated from DJ and RJ measurements using TJ = RJ + DJ. Contributed RJ is calculated for 1×10-12 BER bymultiplying the RMS jitter (measured on a single rise or fall edge) from the oscilloscope by 14. Per FC-PI (Table 9 – SM jitter output, note 1), the actual contributed RJ is allowed to increase above its limit if the actual contributed DJ decreases below its limits, as long as the component output DJ and TJ remain within their specifi ed FC-PI maximum limits with the worst case specified component jitter input.
4. Measured with PRBS 2^7-1 at 10^-12 BER

• Pin Assignment Diagram of Host Board Connector Block Pin Numbers and Name

Diagram of Host Board Connector Block Pin Numbers and Names 

• Pin Function Definitions

Notes:

1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in.
4. Rate select is not used
5. LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
6. AC Coupled

• SFP Module EEPROM Information and Management The SFP modules implement the 2-wire serial communication protocol as defined in the SFP -8472. The serial ID information of the SFP modules and Digital Diagnostic Monitor parameters can be accessed through the I²C interface at address A0h and A2h. The memory is mapped in Table 1. Detailed ID information (A0h) is listed in Table 2. And the DDM specification at address A2h. For more details of the memory map and byte definitions, please refer to the SFF-8472, “Digital Diagnostic Monitoring Interface for Optical Transceivers”. The DDM parameters have been internally calibrated. Table 1. Digital Diagnostic Memory Map (Specific Data Field Descriptions)  

Table 2 - EEPROM Serial ID Memory Contents (A0h)

• Digital Diagnostic Monitor Characteristics

• Regulatory Compliance

 The JHA5440D-53 complies with international Electromagnetic Compatibility (EMC) and international safety requirements and standards (see details in Table following).

• Recommended Circuit 

SFP Host Recommended Circuit

• Mechanical Dimensions 

Mechanical Drawing

JHA reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such products or information.

Published by Shenzhen JHA Technology Co., Ltd

Copyright © Shenzhen JHA Technology Co., Ltd

All Rights Reserved