L3 Managed PoE Switch 4 Port with 2 1G/2.5G/10G SFP Slot | JHA-MT2G05P-L3

Short Description:

* 4-port 100/1000/2500M PoE/PoE+ and 1-port 100/1000/2500M RJ45 and 2-port 100/1000/2500/10000M SFP/SFP+

* 1 port support IEEE802.3af/at/bt,MAX 90W; 2-4 port support IEEE802.3af/at,MAX 30W;

* PoE Pin: Af/at/bt: 12+ 45+ ; 36- 78-; Af/at: 12+ 36-;

* Support QOS, STP/RSTP, IGMP, DHCP, SNMP, WEB etc;

* 3-year warranty


Overview

Related Video

Feature

Specification

Dimension

Order Information

Download

Introduction

JHA-MT2G05P-L3 PoE Switches support 4 100/1000/2500TX PoE/PoE+ and 1 100/1000/2500TX RJ45 and 2 100/1000/2500/10000X SFP/SFP+ Slot, built-in power supply, support QoS, widely used in Ethernet access applications such as small and medium-sized enterprises, Smart cities, security monitoring, and schools.

PoE switch is a kind of network switch that applies Power over Ethernet technology, which transmits both power and data to IP-based terminals (such as IP phones, wireless access APs, IP cameras) through a single twisted-pair cable.

Devices that support PoE can be power sourcing equipment (PSE), powered devices (PD), or sometimes both, the device that transmits power is a PSE, and the device that is powered is a PD. Most PSEs are either network switches or PoE injectors.

PoE technology can automatically detect power consumption of the powered devices and provide the required amount of power to maximize the use of power resources and save costs. On the other hand, non-PoE device intelligently detects no power and only transmits data.

PoE Switches do not need to run additional power cord to connect to the devices, saving the costs of power cables, power outlets, and infrastructure equipment required for electrical installation. PoE powered devices can be easily moved to locations where there is no power outlet, such as wireless network repeaters or IP security cameras because they are usually installed on high walls or ceilings away from power socket.

Power over Ethernet (POE) technology transmits 100M or 1000Mbps data and power budget of 15W, 30W to the devices through Cat5e and Cat6 Ethernet cables at a maximum distance of 100 meters.


  • Previous:
  • Next:

  • Features

    * 4-port 100/1000/2500M PoE/PoE+ and 1-port 100/1000/2500M RJ45 and 2-port 100/1000/2500/10000M SFP/SFP+
    * 1 port support IEEE802.3af/at/bt,MAX 90W; 2-4 port support IEEE802.3af/at,MAX 30W;
    * PoE Pin: Af/at/bt: 12+  45+ ; 36-  78-; Af/at: 12+ 36-;
    * Support QOS, STP/RSTP, IGMP, DHCP, SNMP, WEB, VLAN, ERPS etc.;
    * POE port can be real-time network management, can force POE working mode, real-time display of POE port power.

    Specifications

    Managed PoE Switch Hardware Parameters

    Fixed Port

    4*100/1000/2500M RJ45 PoE

    1*100/1000/2500M RJ45

    2*100/1000/2500/10000M SFP

    PoE Port

    1-4 port supports PoE

    Console Port

    1*console port

    Reset

    1

    Network Protocol

    IEEE 802.3

    IEEE 802.3u 100BASE-TX

    IEEE 802.3ab1000BASE-T

    IEEE 802.3x

    IEEE 802.3z 1000BASE-X

    IEEE 802.3af/at

    IEEE 802.3ad

    IEEE 802.3q 、IEEE 802.3q/p

    IEEE 802.1w、IEEE 802.1d 、IEEE 802.1S

    STP(Spanning Tree Protocol)

    RSTP/MSTP( Rapid Spanning Tree Protocol)

    EPPS ring network protocol

    EAPS ring network protocol

    Port Specification

    10/100/1000/2500BaseT(X)Auto

    Transmission Mode

    Store and Forward(full wirespeed)

    Bandwidth

    512Gbps  

    Packet Forwarding

    89.28Mpps

    MAC Address

    32K

    Buffer

    16M

    Transmission Distance

    10BASE-T : Cat3,4,5 UTP(≤250 meter)

    100BASE-TX : Cat5 or later UTP(≤150 meter)

    1000BASE-TX : Cat6 or later UTP(≤150 meter)

    2500BASE-TX : Cat6 or later UTP(≤100 meter)

    SFP: Support 100M/1G/2.5G/10G SM,DM SFP modules,MAX transmission distance≤120km 

    FLASH

    512M

    RAM

    512M

    Watt

    ≤65W

    LED Indicator

    PWR:Power LED

    SYS:(System LED)

    PoE: Orange PoE LED

    Power

    External power DC52V 1.25A

    (AC:100-240Vac 50-60Hz 0.9A  MAX: 71W) 

    Operating Temperature/Humidity

    -10~+55°C;5%~90% RH Non coagulation

    Storage Temperature/Humidity

    -40~+75°C;5%~95% RH Non coagulation

    Product size/Packing size(L*W*H)

    220mm*112mm*30mm

    265mm*220mm*68mm

    N.W/G.W(kg)

    0.8kg/1.3kg

    Installation

    Desktop(optional wall+machine hanger parts)

    Lightning protection level

    6KV 8/20us;

    IP30

    Features

    L3 Switch

    Port

    Number of Fiber 10G ports

    Maximum 4 ports

    Port Shutdown

    Support

    Port Speed

    Support autonegotiate, full-1000, full-100, half-100, full-10, half-10

    Flow Control

    support full-duplex IEEE 802.3x, half-duplex back pressure

    Storm Control

    Supports rate limit for broadcast, multicast, and DLF packets

    Storm Constrain

    Support the detection of broadcast packets, multicast packets,

    or unicast packets on the port, shutdown the port if the rate is over the threshold.

    Port Mirror

    Support

    Port Rate Limit

    Support port ingress and egress rate limit

    Link Aggregation

    Support manual link aggregation

    Support LACP dynamic link aggregation

    Supports up to 32 aggregation groups, each group up to 8 ports

    Support source MAC, destination MAC, source destination MAC, source IP, destination IP, source destination IP routing strategy

    Port Isolate

    Support

    Jumbo Frame

    Support up to 16KB packet

    Redundant Port

    Support

    The DDM of fiber ports

    Support

    MAC

    MAC Table Capacity

    16K

    MAC Table Management

    Support

    Forwarding mode

    Support IVL forwarding mode

    Static MAC Address

    Support

    MAC Address Binding

    Support

    MAC Address Filtering

    Support

    MAC Learning Control

    Control the MAC learning based on port

    VLAN

    Number of VLANs

    4K

    802.1q-based VLAN

    Support

    MAC-based VLAN

    Support

    IP-based VLAN

    Support

    Protocol-based VLAN

    Support

    PVLAN

    Support

    Voice VLAN

    Support

    VLAN Mapping

    Support 1:1 mapping

    QinQ

    Support basic QinQ

    Support flexible QinQ

    Reliability

    Spanning Tree Protocol

    Support STP/RSTP/MSTP

    Port Loop Detection

    Support

    EAPS

    Support RFC3619

    ERPS

    Support G.8032/Y.1344

    LLDP

    Support LLDP & LLDP-MED

    UDLD

    Fully compatible with CISCO’s UDLD protocol

    VLLP (VRRP Layer-2 Loop Protection)

    Support, Only used with VRRP

    L3

    ARP

    Support static and dynamic ARP

    Static Route

    Support static route based on IPv4 and IPv6

    VLAN Interface

    Support 32 VLAN interfaces

    RIP

    Support RIP v1/v2 & IPv6 RIPng

    OSPF

    Support OSPFv2 & IPv6 OSPFv3

    BGP

    Support BGP4 & IPv6 BGP4+

    Policy Route

    Support

    VRRP

    Support

    Multicast

    Static Multicast MAC Address

    Support

    IGMP SNOOPING

    Support IGMP SNOOPING v1/v2/v3

    Support IGMP Querier

    Support IGMP SNOOPING Filter

    MVR

    Support

    GMRP

    Support

    IGMP

    Support IGMP v1/v2/v3

    PIM-SM

    Support

    ACL

    Standard IP-based ACL

    Support

    Extended IP based ACL

    Support

    MAC IP-based ACL

    Support

    MAC ARP-based ACL

    Support

    ACL Port Filtering

    Support

    Time-based ACL

    Support

    QoS

    Port Queue Number

    8

    Port Queue Scheduling Mode

    Support WRR,RR,WDRR,SP

    Port-based Classification

    Support

    802.1p-based Classification

    Support

    DSCP-based Classification

    Support

    ACL-based Classification

    Support

    QoS Policy

    Support packets mapping to queue

    Support COS or DSCP Remarking

    Support rate limits of data flow

    Support data flow statistics

    Support mirroring of data flow

    DHCP

    DHCP Client

    Support

    DHCP Snooping

    Support

    DHCP Relay

    Support

    DHCP Server

    Support

    DHCP option 82

    Support

    Management

    CLI  Management

    Support Console, Telnet and SSH

    Support multiple TELNET connections based on IPv4 and IPv6

    Support multiple SSH connections based on IPv4 and IPv6

    WEB Management

    Support HTTP based on IPv4 and IPv6

    Support HTTPS based on IPv4 and IPv6

    SNMP Management

    Support SNMP v1, v2c, v3

    Support SNMP TRAP

    Support lots of standard and private MIBs

    Support SNMP and TRAP based on IPv4 and IPv6

    User Management

    Support multiple user management

    TACACS+

    support switch authentication via TACACS+ server remote username and password

    Support password encryption in PAP and CHAP mode

    Support TACACS+ server to authorize the switch’s commands

    Support TACACS+ based on IPv4 and IPv6

    Log Management

    Support local log management

    Support SYSLOG

    RMON

    Support RMON 1, 2, 3 and 9 groups

    Cluster Management

    Support NDP

    Support NTDP

    Support manual and automatic joining of cluster groups

    Support cluster unified management

    Configuration File

    Support uploading and downloading configuration file

    Support TFTP transmission based IPv4 and IPv6

    Upgrade software

    Support TFTP transmission based IPv4 and IPv6

    Clock Management

    Support local clock management

    Support SNTP

    Security

    Switch Management Security

    Support enabling and disabling TELNET、SSH、HTTP、HTTPS and SNMP services

    Support TELNET、SSH、HTTP、HTTPS and SNMP services to bind to standard IP ACLs

    Support for limiting the number of TELNET and SSH connections

    CPU Protection

    The switch’s own security protection prevents large data streams from attacking the switch itself.

    AAA

    Support 802.1x

    Support RADIUS

    Supports authentication, authorization, and accounting through RADIUS server

    Support port-based and MAC-based 802.1x

    Support 802.1x guest VLAN

    IP MAC Binding

    Support static configuration of IP, MAC and port binding

    DHCP SNOOPING

    Support dynamic ARP binding to prevent ARP spoofing

    Support dynamic IP, MAC and port binding

    Support fixed port to connect to DHCP server to prevent private connection to DHCP server

    Prevent ARP Spoofing

    Support manually configuring MAC ARP-based ACL rules to prevent ARP spoofing.

    Support the DHCP SNOOPING function. During the process of obtaining an IP address by DHCP, the switch dynamically binds ARP to the port to prevent ARP spoofing.

    POE

    Switch Control

    Support POE powering of ports on and off

    Power Control

    Support setting total power

    Other Advanced Features

    Support POE scheduling policy and PD online query, etc.

    IPv6

    IPv4/IPv6 Dual Protocol Stack

    Support

    IPv6 Address

    Support manual address configuration and stateless address auto-configuration

    IPv6 Neighbor Discovery

     

    Support

    ICMPv6

    Support

    IPv6 Path MTU Discovery

    Support

    Debugging

    PING

    Support

    PING6

    Support

    TRACEROUTE

    Support

    TELNET Client

    Support TELNET client based IPv4 and IPv6

    SSH Client

    Support SSH client based IPv4 and IPv6

    Order Information

    Model NO.

    Description

    JHA-MT2G05P-L3

    L3 managed PoE switch, 4-port 100/1000/2500M PoE/PoE+ and 1-port 100/1000/2500M RJ45 and 2-port 100/1000/2500/10000M SFP/SFP+ Slot,built in power supply

  • pdf
    JHA-MT2G05P-L3 Datasheet
    pdf
  • Write your message here and send it to us