10G BASE-T Copper SFP+ Transceiver JHA3901G
Features:
◊ Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T
◊ Hot-pluggable SFP footprint
◊ Compact RJ-45 connector assembly
◊ RoHS compliant and lead-free
◊ Single +3.3V power supply
◊ 10 Gigabit Ethernet over Cat 6a cable
◊ Ambient Operating temperature: 0°C to +70°C
Applications:
◊ 10G Ethernet over Cat 5 cable
◊ Switch/Router to Switch/Router Link
◊ High speed I/O for file severs
Description:
JHA3901G SFP+-10GBASE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA) . They are compatible with the 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T standards as specified in IEEE Std 802.3 . SFP+-10GBASE-T uses the SFP’s RX_LOS(must be pulled up on host) pin for link indication. If pull up or open SFP’s TX_DISABLE pin, PHY IC be reset.
• SFP to Host Connector Pin Out
|
Pin |
Symbol |
Name/Description |
Ref. |
|
1 |
VEET |
Transmitter Ground (Common with Receiver Ground) |
1 |
|
2 |
TFAULT |
Transmitter Fault. Not supported. |
|
|
3 |
TDIS |
Transmitter Disable. Laser output disabled on high or open. |
2 |
|
4 |
MOD_DEF(2) |
Module Definition 2. Data line for Serial ID. |
3 |
|
5 |
MOD_DEF(1) |
Module Definition 1. Clock line for Serial ID. |
3 |
|
6 |
MOD_DEF(0) |
Module Definition 0. Grounded within the module. |
3 |
|
7 |
Rate Select |
No connection required |
|
|
8 |
LOS |
High indicates no linked. low indicates linked. |
4 |
|
9 |
VEER | Receiver Ground (Common with Transmitter Ground) |
1 |
|
10 |
VEER | Receiver Ground (Common with Transmitter Ground) |
1 |
|
11 |
VEER | Receiver Ground (Common with Transmitter Ground) |
1 |
|
12 |
RD- |
Receiver Inverted DATA out. AC Coupled |
|
|
13 |
RD+ |
Receiver Non-inverted DATA out. AC Coupled |
|
|
14 |
VEER |
Receiver Ground (Common with Transmitter Ground) |
1 |
|
15 |
VCCR |
Receiver Power Supply |
|
|
16 |
VCCT |
Transmitter Power Supply |
|
|
17 |
VEET |
Transmitter Ground (Common with Receiver Ground) |
1 |
|
18 |
TD+ |
Transmitter Non-Inverted DATA in. AC Coupled. |
|
|
19 |
TD- |
Transmitter Inverted DATA in. AC Coupled. |
|
|
20 |
VEET |
Transmitter Ground (Common with Receiver Ground) |
1 |
Notes:
1. Circuit ground is connected to chassis ground
2. PHY disabled on TDIS > 2.0V or open, enabled on TDIS < 0.8V
3. Should be pulled up with 4.7k – 10k Ohms on host board to a voltage between 2.0 V and 3.6 V. MOD_DEF(0) pulls line low to indicate module is plugged in.
4. LVTTL compatible with a maximum voltage of 2.5V.
Figure 1. Diagram of host board connector block pin numbers and names
• Cable Length
|
Standard |
Cable |
Reach |
Host Port |
|
10Gbase-T |
CAT6A |
30m |
XFI |
|
5Gbase-T/2.5Gbase-t |
CAT5E |
50m |
5GBase-R/2.5GBase-X |
|
1000base-T |
CAT5E |
100m |
1000base-FX |
• +3.3V Volt Electrical Power Interface
The JHA3901G SFP+-10GBASE-T has an input voltage range of 3.3 V +/- 5%. The 4V maximum voltage is not allowed for continuous operation.
|
+3.3 Volt Electrical Power Interface |
||||||
|
Parameter |
Symbol |
Min |
Typ |
Max |
unit |
Notes/Conditions |
|
Supply Current |
Is |
|
700 |
900 |
mA |
3.0W max power over full range of voltage and temperature. See caution note below |
|
Input Voltage |
Vcc |
3.13 |
3.3 |
3.47 |
V |
Referenced to GND |
|
Maximum Voltage |
Vmax |
|
|
4 |
V |
|
|
Surge Current |
Isurge |
|
TBD |
|
mA |
Hot plug above steady state current. See caution note below |
Caution: Power consumption and surge current are higher than the specified values in the SFP MSA
• Low-Speed Signals
MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals. Both MOD_ DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc.
|
Low-Speed Signals, Electronic Characteristics |
|||||
|
Parameter |
Symbol |
Min |
Max |
unit |
Notes/Conditions |
|
SFP Output LOW |
VOL |
0 |
0.5 |
V
|
4.7k to 10k pull-up to host_Vcc, measured at host side of connector |
|
SFP Output HIGH |
VOH |
host_Vcc -0.5 |
host_Vcc + 0.3 |
V
|
4.7k to 10k pull-up to host_Vcc,measured at host side of connector |
|
SFP Input LOW |
VIL |
0 |
0.8 |
V |
4.7k to 10k pull-up to Vcc,measured at SFP side of connector
|
|
SFP Input HIGH |
VIH |
2 |
Vcc + 0.3 |
V |
4.7k to 10k pull-up to Vcc,
measured at SFP side of connector |
• High-Speed Electrical Interface
All high-speed signals are AC-coupled internally.
|
High-Speed Electrical Interface, Transmission Line-SFP |
||||||
|
Parameter |
Symbol |
Min |
Typ |
Max |
unit |
Notes/Conditions |
|
Line Frequency |
fL |
|
125 |
|
MHz |
5-level encoding, per IEEE 802.3 |
|
Tx Output Impedance |
Zout,TX |
|
100 |
|
Ohm |
Differential, for all frequencies between 1MHz and 125MHz |
|
Rx Input Impedance |
Zin,RX |
|
100 |
|
Ohm |
Differential, for all frequencies between 1MHz and 125MHz |
|
High-Speed Electrical Interface, Host-SFP |
||||||
|
Parameter |
Symbol |
Min |
Typ |
Max |
unit |
Notes/Conditions |
|
Single ended data input swing |
Vinsing |
250 |
|
1200 |
mV
|
Single ended |
|
Single ended data output swing |
Voutsing |
350 |
|
800 |
mV |
Single ended |
|
Rise/Fall Time |
Tr,Tf |
|
175 |
|
psec |
20%-80% |
|
Tx Input Impedance |
Zin |
|
50 |
|
Ohm |
Single ended |
|
Rx Output Impedance |
Zout |
|
50 |
|
Ohm |
Single ended |
• General Specifications
|
General |
||||||
|
Parameter |
Symbol |
Min |
Typ |
Max |
unit |
Notes/Conditions |
|
Data Rate |
BR |
1 |
|
10 |
Gb/sec |
IEEE 802.3 compatible. See Notes 1,2 below |
Notes:
- Clock tolerance is +/- 50 ppm
• Environmental Specifications
Automatic crossover detection is enabled. External crossover cable is not required
|
Environmental Specifications
|
||||||
|
Parameter |
Symbol |
Min |
Typ |
Max |
unit |
Notes/Conditions |
|
Operating Temperature |
Top |
0 |
|
65 |
°C |
Case temperature |
|
Storage Temperature |
Tsto |
-40 |
|
85 |
°C |
Ambient temperature |
• Serial Communication Protocol
All SFPs support the 2-wire serial communication protocol outlined in the SFP MSA. These SFPs use an MCU, can be accessed with address of A0h.
|
Serial Bus Timing, Requirements |
||||||
|
Parameter |
Symbol |
Min |
Typ |
Max |
unit |
Notes/Conditions |
|
I 2C Clock Rate |
|
0 |
|
200,000 |
Hz |
|
• EEPROM INFORMATION（A2）,optional
• Recommended Application Circuit
• Serial ID Memory Contents
|
Addr |
Field Size (Bytes) |
Name of Field |
HEX |
Description |
|
0 |
1 |
Identifier |
03 |
SFP |
|
1 |
1 |
Ext. Identifier |
04 |
MOD4 |
|
2 |
1 |
Connector |
22 |
RJ45 |
|
3-10 |
8 |
Transceiver |
00 00 00 00 00 00 00 00 |
Transmitter Code |
|
11 |
1 |
Encoding |
06 |
64B66B |
|
12 |
1 |
BR, nominal |
67 |
10000M bps |
|
13 |
1 |
Reserved |
00 |
|
|
14 |
1 |
Length (9um)-km |
00 |
|
|
15 |
1 |
Length (9um) |
00 |
|
|
16 |
1 |
Length (50um) |
00 |
|
|
17 |
1 |
Length (62.5um) |
00 |
|
|
18 |
1 |
Length (copper) |
1E |
30m |
|
19 |
1 |
Reserved |
00 |
|
|
20-35 |
16 |
Vendor name |
JHA Technology Co., Ltd |
|
|
36 |
1 |
Reserved |
00 |
|
|
37-39 |
3 |
Vendor OUI |
00 00 00 |
|
|
40-55 |
16 |
Vendor PN |
JHA3901G |
ASC II |
|
56-59 |
4 |
Vendor rev |
31 2E 30 20 |
V1.0 |
|
60-61 |
2 |
Wavelength |
00 00 |
850nm |
|
62 |
1 |
Reserved |
00 |
|
|
63 |
1 |
CC BASE |
XX |
Check sum of byte 0~62 |
|
64-65 |
2 |
Options |
00 1A |
LOS, TX_DISABLE, TX_FAULT |
|
66 |
1 |
BR, max |
00 |
|
|
67 |
1 |
BR, min |
00 |
|
|
68-83 |
16 |
Vendor SN |
|
Unspecified |
|
84-91 |
8 |
Vendor date code |
XX XX XX 20 |
Year, Month, Day |
|
92-94 |
3 |
Reserved |
00 |
|
|
95 |
1 |
CC_EXT |
XX |
Check sum of byte 64~94 |
|
96-255 |
160 |
Vendor specific |
|
|
• Mechanical Dimensions
Mechanical Dimensions of Transceiver
JHA reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such products or information.
Published by Shenzhen JHA Technology Co., Ltd
Copyright © Shenzhen JHA Technology Co., Ltd
All Rights Reserved
